Screen enclosures in Naples: a city sub-permit or a county permit
Not every address that says Naples is inside the city. Within the City of Naples, the Building Department's pool checklist calls fences, walls and screen enclosures accessory structures that must be permitted separately from the pool. The city's pool application lists aluminum screen enclosure work as its own sub-permit, beside gas, electrical and fence work.
North Naples and East Naples are unincorporated Collier County. There a cage falls under the county's Aluminum Structure permit. That permit calls for construction plans, a site plan and a final spot survey with a note naming the screen-enclosed pool area, if the cage goes over a permitted pool. If your street is outside the city, the pages on screen enclosures in North Naples and East Naples walk that route.
We ask the right office about your address before we draw a line. The City of Marco Island and Lee County keep separate desks of their own, so a neighbor's answer from there doesn't carry over. The rest of what we build in town is on the Naples page.
Pool cage designs for Port Royal, Aqualane Shores and Park Shore lots
In the early 1950s John Glenn Sample dredged Port Royal out of Naples Bay marshland, and its streets still carry pirate names like Gin Lane and Galleon Drive. That dredging also spurred Aqualane Shores, Park Shore and Moorings. Water covers 25.09 percent of the city's 16.4 square miles, so the view past the cage shapes the design from the first sketch.
The view is where custom pool cages earn their price. Picture-window panels keep the sightline open. Panoramic pool enclosure designs, with fewer vertical members, run $25,000 to $80,000+ per job. Mansard and gable rooflines can echo the house. We size the frame around your pool, deck and any association rules, so the cage looks built in.
Height starts at the ground. According to the city's checklist, a pool and deck outside the building envelope can't exceed 30 inches above crown of road (36 inches in the R1-15A district) except as Code Sec. 56-45 allows. Construction also stops after the slab until an Elevation Certificate and a Spot Survey are approved, so a cage built with a new pool waits on that approval too.
What the wind table asks of a pool enclosure contractor
Under Florida's building code a cage counts as an aluminum structure, and Chapter 20 spells out the rules. Extruded aluminum members must have an actual wall thickness of at least 0.040 inch. Table 2002.4 supplies the wind loads for two directions, and every main member also carries a 300-pound vertical load on any 1 foot. Take a design wind speed of 150 mph in Exposure C. The table gives 43 psf horizontal on the windward face, 34 psf on the leeward face, 12 psf vertical on screen and 45 psf vertical on solid surfaces. At 160 mph the same lines read 49, 39, 14 and 51 psf.
Vinyl, tempered glass and acrylic panels have to be removable, and each carries a decal stating the removable panel shall be removed when wind speeds exceed 75 mph. Per its Wind Zone Map, Collier County puts its minimum design wind speed for a Category II structure at 150 mph, and some regions can run as high as 170 mph. Which number belongs to your address? The Building Department and the sealed drawing will tell you. A guess won't.
So pool enclosure contractors should hand you the engineering before the deposit. The hurricane code guide goes through the table line by line.
Pool cage companies, installers and a house that sits empty in summer
In the 2020 census the city had 18,225 housing units, and 46.1 percent were vacant on census day. If yours is a house you leave for the summer, nobody is around to watch the cage June through October. Hurricane Ian in 2022 did about $989 million in damage to the city and knocked out power for days. Going back to 1851, the area has seen 74 tropical storms within 85 nautical miles.
That changes what you ask pool cage companies and pool cage installers. Who files the permit? Is the drawing signed and sealed? Which panels come out ahead of a storm, and who takes them down while you're up north? Put those same four questions to every bidder, and compare what they write back. Our estimate names the frame, the screen, the panel type and who files the sub-permit.
Resurfacing, a deck or a spa can share a schedule with screen enclosures in Naples. Look at pool resurfacing in Naples, pool decks in Naples and spas and water features in Naples.
Getting screen enclosures in Naples priced from a walk around your lanai
A new aluminum cage typically runs $9 to $16 per sq ft, and a typical job lands between $15,000 and $35,000. Say the cage is 1,800 sq ft. At those rates that's $16,200 to $28,800. Rescreening an existing frame runs $3 to $6 per sq ft, so the same area costs $5,400 to $10,800. We visit and take measurements. You then get a free written estimate with the frame, the panels and the permit route written out.
For screen enclosures in Naples, have your survey handy if you own one, and the name of your association, if there is one. The screen enclosures page explains the job end to end. Call (239) 899-6371 or use the contact page.
Sources
- Pool/Spa (Private) permit checklist (Residential Pool 2026.10.01), City of Naples Building Department
- Private Residential Swimming Pool/Spa Permit Application, City of Naples Building Department
- Aluminum Structures (PRAS), Collier County Growth Management
- 2023 FBC-Building, Chapter 20 Aluminum, ICC / UpCodes
- Florida Building Code 8th Edition 2023 Formal Interpretation, Collier County Building Plan Review & Inspection
- Naples, Florida, Wikipedia
- Coastal Construction Control Line Program, Florida Department of Environmental Protection




